Putting a WiFi QR code into Word, PowerPoint or Canva

Plenty of people can generate a code and still fail at the last step: drop it into a document, print, and nothing scans. The cause is almost always one of two things — the image was compressed, or its size was computed in screen pixels.

1. Word does not generate QR codes

Word, Excel and PowerPoint have no built-in QR encoder and no way to produce a WIFI:T:WPA;S:…;P:…;; payload. The workflow is always "generate first, lay out second":

2. Size: pick millimetres, then derive pixels

Print sizing is in millimetres; software often reports pixels. That mismatch is the usual failure point. The table converts at 300 dpi and can be used directly as an export size.

Code edgePixels @300 dpiTypical use
30 mm≈ 355 pxBusiness cards, small table stands
40 mm≈ 472 pxA5 table tents, in-room cards
50 mm≈ 591 pxStandard A4 poster, scanned within 1 m
80 mm≈ 945 pxA3, entrance stands, 1.5–2 m
120 mm≈ 1417 pxBanners, windows, 3 m away

Add the quiet zone: at least four modules of white all round (usually 2–3 mm), never flush against a colour block or an image edge.

3. Three settings in Word

In order

  1. Disable image compression: File → Options → Advanced → Image size and quality, tick "Do not compress images in file", set default resolution to high fidelity or 300 ppi. Skip this and quality drops on insert.
  2. Insert, then set exact size: right-click → Size and Position, type centimetres (5 cm × 5 cm) instead of dragging.
  3. Set wrapping to "in front of text": easier to position on the card and it won't be squeezed by line spacing.

Any PDF preset works for export, but print at actual size — don't let the reader scale for you.

4. Two traps in PowerPoint

5. Canva: usage and pitfalls

  1. Upload a PNG already sized in pixels for the millimetres you want (50 mm → 591 px). Never upload small and scale up.
  2. Type millimetres into Position → Size rather than eyeballing alignment.
  3. Download as "PDF Print" to avoid recompression; "PNG" also works if the export size is large enough.
  4. No rounded-corner masks, drop shadows or gradient overlays on the code — all three blur module edges.

6. Five checks before printing

CheckPass condition
ScalePrint dialog at 100% / actual size, "fit to page" off
Measured sizeDiagonal within 1 mm of the design value
Quiet zoneWhite margin visible on paper, not trimmed
Phone testScan once on iOS and once on Android, from the real distance
ContrastDark modules on a light background — never invert

PNG or SVG, one click apart

Enter the SSID and password, export 300 dpi PNG, SVG or a full-page PDF, sized in millimetres.

Open the WiFi QR studio

Related guides

Frequently asked questions

Can Word generate a WiFi QR code by itself?
No. Word has no QR encoder and no WIFI: payload support. Generate the code online, export a 300 dpi PNG or an SVG, then insert and lay it out in Word.
Why does the inserted image look blurry?
Word's image compression. Open File → Options → Advanced → Image size and quality, tick 'Do not compress images in file', set the default resolution to high fidelity or 300 ppi, then re-insert the picture.
It looks sharp on screen but won't scan after printing. Why?
A 200×200 px image placed at a few centimetres on A4 is roughly 90 dpi — well below the 300 dpi print target. Export pixels from millimetres, or use SVG/PDF vectors.
Does Canva's PDF Print download improve quality?
It avoids recompression, so it helps — but only if the uploaded PNG was already sized for print. A small image enlarged will not sharpen just because the output is PDF.
Should I turn off 'fit to page' when printing?
Yes. Scaling can shrink a 5 cm code to 4.6 cm and shift module alignment, leaving half-pixel blur at the edges. Choose actual size / 100%.

Templates that fit this setup

Three layouts picked for this scenario — swap the venue name and password, then export.