How much logo a QR code can take

A QR symbol carries error-correction data, which is exactly why a logo can sit in the middle. The usable margin is smaller than most people assume, and passing it fails quietly: some phones scan, some do not.

1. The four levels and what each buys

LevelRecoverable area (theory)Suitable for
Labout 7%On-screen, clean, no obstructions
Mabout 15%Normal print, no logo or a tiny one
Qabout 25%The practical floor when adding a logo
Habout 30%Logo plus wear, outdoor or glare

These are ceilings for a clean read, not targets. Real conditions add losses: smudged lenses, screen reflections, ink bleed, an oblique camera angle. Budget well below the table.

2. What must never be covered

Three no-go zones

  • The three finder patterns — the square-in-square blocks at top-left, top-right and bottom-left. They tell the scanner that this is a symbol and how it is rotated.
  • The timing lines — the alternating row and column between the finders, used to estimate the grid.
  • Alignment patterns near the right and bottom edges, which correct perspective distortion on larger matrices.

That is why the logo belongs in the centre. Placing it over a corner may look more balanced, but it removes part of the symbol's skeleton.

3. Area limit: 20% is the working number

Keep the logo's side below 45% of the code's side — roughly 20% of its area — at level Q. At H you can go to 50% of the side, about 25% of the area. Past that, the success rate drops sharply as light gets worse.

A quick test beats any table: shrink the finished artwork to 5 cm on a phone screen and scan it with two phones, once in normal light and once dimmed. If one needs several attempts at an angle, shrink the logo or raise the level.

4. The ring around the logo is functional

A dark logo on dark modules merges into one blob the scanner cannot segment. A ring one or two modules wide keeps them apart, and it looks cleaner too.

5. A logo costs you physical size

Raising error correction enlarges the matrix. At fixed physical size, modules get smaller and printing gets harder — ink spread, paper texture, laminate haze all matter more. Plan one to two steps larger: a 5 cm code without a logo becomes 6.5–8 cm with one.

The full distance-to-size table is in the printing guide; how content length changes the matrix is covered in the payload guide.

6. Failure modes and fixes

SymptomLikely causeFix
Some phones scan, others do notLogo close to the limit; weaker cameras fail in dim lightReduce logo to 40% of the side, or move to H
Face-on works, angled failsAlignment patterns obstructedCentre and shrink the logo
Fine on screen, dead in printDenser matrix plus ink bleedPrint larger, export vector
Grey halo around the logoPNG uploaded with a white background on a tinted posterUpload a transparent PNG, ring in background colour

7. Three checks before you publish

  1. Decode with a scanner app and compare SSID and password character by character — "it connected" is not proof.
  2. Scan with an iPhone and an Android, one of them with the screen dimmed.
  3. Step back to 1.5× the intended distance and scan again for margin.

Tune the logo and the level in the studio

Upload a transparent logo, preview the centred ring, switch error correction and export a vector file.

Open the WiFi QR studio

Related guides

Frequently asked questions

Can a WiFi QR code have a logo in the middle?
Yes, provided error correction is raised to Q or H and the logo area is kept small. The centre is data territory; damaged modules there can be rebuilt from the error-correction codewords. The three finder patterns and timing lines must never be covered.
How much do the four error-correction levels differ?
L recovers roughly 7% of the symbol, M 15%, Q 25% and H 30%. Those are theoretical ceilings for a clean read, so real designs should stay below them: Q is the practical floor for a logo, H is safer but produces a denser grid.
What is the largest logo I can use?
Keep the logo inside about 20% of the code area at Q, 25% at H — in practice a logo whose side is under 45% of the code's side. Beyond that, scanning starts failing in dim light or at an angle.
Does the logo need a white ring?
Yes. A ring one or two modules wide separates the artwork from the data modules, so dark-on-dark does not merge into an unreadable blob. Use the background colour if the background is not white.
Why does adding a logo force a bigger print?
Higher error correction enlarges the matrix. At the same physical size each module gets smaller, so inkjet bleed and paper texture eat into it. Plan one to two size steps larger than the logo-free version.

Templates that fit this setup

Three layouts picked for this scenario — swap the venue name and password, then export.